- 您现在的位置：买卖IC网 > Sheet目录323 > DSP56311EVM (Freescale Semiconductor)KIT EVALUATION FOR DSP56311
Host Interface (HI08)
Table 6-15. Interface Control Register (ICR) Bit Definitions (Continued)
Bit Number
1
Bit Name
TREQ
Reset Value
0
Transmit Request Enable
Description
Enables host requests via the host request (HREQ or HTRQ) signal when the
transmit data register empty (TXDE) status bit in the ISR is set. If TREQ is
cleared, TXDE interrupts are disabled. If TREQ and TXDE are set, the host
request signal is asserted.
TREQ and RREQ modes (HDRQ = 0)
TREQ
RREQ HREQ Signal
0
0
1
1
0
1
0
1
No interrupts (polling)
RXDF request (interrupt)
TXDE request (interrupt)
RXDF and TXDE request (interrupts)
TREQ and RREQ modes (HDRQ = 1)
TREQ
RREQ HTRQ Signal
HRRQ Signal
0
0
No interrupts (polling)
No interrupts
(polling)
0
1
No interrupts (polling)
RXDF request
(interrupt)
1
1
0
1
TXDE request
(interrupt)
TXDE request
(interrupt)
No interrupts
(polling)
RXDF request
(interrupt)
0
RREQ
0
Receive Request Enable
Controls the HREQ signal for host receive data transfers. RREQ enables host
requests via the host request (HREQ or HRRQ) signal when the receive data
register full (RXDF) status bit in the ISR is set. If RREQ is cleared, RXDF
interrupts are disabled. If RREQ and RXDF are set, the host request signal
(HREQ or HRRQ) is asserted.
6.7.2 Command Vector Register (CVR)
The host processor uses the CVR, an 8-bit read/write register, to cause the DSP56311 to execute
an interrupt. The host command feature is independent of any of the data transfer mechanisms in
the HI08. It causes execution of any of the 128 possible interrupt routines in the DSP core.
Hardware, software, individual, and stop resets clear the CVR bits.
7
HC
6
HV6
5
HV5
4
HV4
3
HV3
2
HV2
1
HV1
0
HV0
Figure 6-16. Command Vector Register (CVR)
DSP56311 User’s Manual, Rev. 2
6-24
Freescale Semiconductor
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DSPAUDIOEVMMB1E
BOARD MOTHER DSP563XX
DSPIC30F2010 DEVELOPMENT KIT
KIT DEV EMBEDDED C
DSTRM-KT-0181A
DSTREAM DEBUG AND TRACE UNIT
DSUT1CSU
SURGE SUPPR NETWORK W/GROUND
DTEL2
SURGE SUPPRESSOR PHONE RJ11/RJ45
DV003001
PROGRAMMER PICSTART PLUS 16C/17C
DV164035
MPLAB ICD3 IN-CIRC DEBUGGER
DV164039
KIT DEV PIC24FJ256DA210
相关代理商/技术参数
DSP56311EVMIG_D
制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311EVMIG DSP56311EVM Sample Code
DSP56311EVMUM
制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311 Evaluation Module Hardware Reference Manual
DSP56311FACT
制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311 Higher performance programmable DSP for demanding voice and data applications
DSP56311UM
制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311 24-Bit Digital Signal Processor Users Manual
DSP56311UMAD
制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56311 Users Manual Addendum
DSP56311VF150
功能描述:数字信号处理器和控制器 - DSP, DSC 150Mhz/300MMACS 150Mhz EFCOP RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSP56311VF150B1
功能描述:数字信号处理器和控制器 - DSP, DSC 24 BIT DSP
RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSP56311VF150R2
功能描述:数字信号处理器和控制器 - DSP, DSC 24 BIT DSP RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
